View BU4051BCFV-E2_9030661.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

product structure : silicon monolithic integrated circuit this product has no designed protection against radioactive ra ys . 1/ 17 tsz02201-0rdr0gz00280-1-2 ? 20 15 rohm co., ltd. all rights reserved. 06.jan.2015 rev.001 tsz22111 ? 14 ? 001 www.rohm.com general purpose cmos logic ic 8ch analog multiplexer/demultiplexer bu4051bc bu4051bcf bu4051bcfv general description t he bu40 51 bc , bu4051b cf , bu4051bcfv are multiplexers/demultiplexers with capabilities of selectio n and mixture of analog signal and digital signal. this series are configur ed with 8channels input/output.the digital signal of the control terminal turns on the corresponding switch of each channel. the large am plitude voltage (v dd -v ee ) can be switched by the control signal with small logical amplitude voltage (v dd -v ss ). features ? low power consumption ? wide operating supply voltage ? high input impedance truth table key specifications ? operating supply voltage range: 3v to 18v ? input voltage range(control): v ss to v dd ? input/output voltage range(switch): v ee to v dd ? operating temperature range: - 40 c to +85c packag es w(typ) x d(typ) x h(max) di p 16 19.40mm x 6.50mm x 7.95 mm sop 16 10.00mm x 6.20mm x 1.71mm ss op -b 16 5.00mm x 6.40mm x 1.35 mm control on switch inhibit a b c l l l l x0 l h l l x1 l l h l x2 l h h l x3 l l l h x4 l h l h x5 l l h h x6 l h h h x7 h don t care don t care don t care none dip16 sop16 ssop- b1 6 datashee t downloaded from: http:///
2/ 17 tsz02201-0rdr0gz00280-1-2 ? 20 15 rohm co., ltd. all rights reserved. 06.jan.2015 rev.001 www.rohm.com tsz22111 ? 15 ? 001 bu40 51 bc bu40 51 bcf bu4051bcfv pin configuration pin description pin no. pin name i/o function 1 i /o analog switch input / output 2 x6 i/o analog switch input / output 3 x i/o analog switch input / output 4 x7 i/o analog switch input / output 5 x5 i/o analog switch input / output 6 inhibit i control input 7 vee D power supply(-) 8 vss D power supply(-) 9 c i control input 10 b i control input 11 a i control input 12 x3 i/o analog switch input / output 13 x0 i/o analog switch input / output 14 x1 i/o analog switch input / output 15 x2 i/o analog switch input / output 16 vdd D power supply (+) 1 2 4 5 6 7 14 13 12 9 x4 x0 a b c x3 11 3 10 x1 x6 x x7 x5 inhibit vee 8 vss 15 x2 16 vdd x4 (top view) downloaded from: http:///
3/ 17 tsz02201-0rdr0gz00280-1-2 ? 20 15 rohm co., ltd. all rights reserved. 06.jan.2015 rev.001 www.rohm.com tsz22111 ? 15 ? 001 bu40 51 bc bu40 51 bcf bu4051bcfv block diagram absolute maximum ratings (t a =25c) parameter symbol rating unit supply voltage (note 1) v dd - 0. 5 to + 20 .0 v control input voltage v c in (v ss - 0.5) ~ (v dd +0. 5) v analog switch input/output voltage v in / v out (v ee - 0.5) ~ (v dd +0. 5) v control input current i c in 10 ma operating temperature t opr - 40 to + 85 c storage temperature t stg - 55 to + 150 c maximum junction temperature t j max + 150 c power dissipation p d dip16 1.25 (note 2) w sop16 0.62 (note 3) ssop-b16 0.87 (note 4) (note 1) it contain voltage of v ss to v dd and voltage of v ee to v dd . it shoud be v ee v ss (note 2) mounted on 70mm x 70mm x 1.6mm glass epoxy board. reduce 10.0 mw per 1 c above 25 c (note 3) mounted on 70mm x 70mm x 1.6mm glass epoxy board. reduce 5 .0mw per 1 c above 25 c (note 4) mounted on 70mm x 70mm x 1.6mm glass epoxy board. reduce 7.0mw per 1 c above 25 c caution: operating the ic over the absolute maximum ratings may damage the ic. t he damage can either be a short circuit between pins or an open circuit between pins and the internal circuitry. therefore , it is important to consider circuit protection measures, such as adding a fuse, in case the ic is operated over the absolute maximum ratings. recommended operating conditions (t a = - 40 c to +85 c ) parameter symbol min typ max unit supply voltage v dd 3.0 - 18 v control input voltage v c in v ss - v dd v analog switch input/output voltage v in / v out v ee - v dd v common x vdd inhibit a b c vss vee x0 x1 x2 x3 x4 x5 x6 x7 level converter binary to 1 of 8 decoder with inhibit downloaded from: http:///
4/ 17 tsz02201-0rdr0gz00280-1-2 ? 20 15 rohm co., ltd. all rights reserved. 06.jan.2015 rev.001 www.rohm.com tsz22111 ? 15 ? 001 bu40 51 bc bu40 51 bcf bu4051bcfv electrical characteristics (unless otherwise specified v ss =0v, v ee =0v, t a =25c) parameter symbol min typ max unit conditions dc characteristics input h voltage v ih 3.5 - - v v dd =5v - 7.0 - - v dd =10v 11.0 - - v dd =15v input l voltage v il - - 1.5 v v dd =5v - - - 3.0 v dd =10v - - 4.0 v dd =15v input h current i ih - - 0.3 a v dd =15v v ih =15v input l current i il - - -0.3 a v dd =15v v il =0v on resistance r on - - 950 v dd =5v - - - 250 v dd =10v - - 160 v dd =15v on resistance defluxion r on - 10 - v dd =5v - - 6 - v dd =10v - 4 - v dd =15v channel-off leakage current i off - - 0.3 a v dd =15v common=0v - - -0.3 v dd =15v common=vdd quiescent supply current i dd - - 5 a v dd =5v v in =v dd or v ee - - 10 v dd =10v - - 15 v dd =15v switching characteristics, c l =50pf propagation delay time inout t plh t phl - 15 45 ns v dd =5v - - 8 20 v dd =10v - 6 15 v dd =15v propagation delay time control (a,b,c) out t phz ,t plz t pzh ,t pzl - 170 550 ns v dd =5v - - 90 240 v dd =10v - 70 160 v dd =15v propagation delay time control (inhibit) out t phz ,t plz t pzh ,t pzl - 150 450 ns v dd =5v - - 70 210 v dd =10v - 50 160 v dd =15v maximum propagation frequency f max - 20 - mhz v dd =5v v ee =- 5v feed through attenuation f t - 0.5 - mhz v dd =5v v ee =- 5v sine wave distortion d - 0.02 - % v dd =5v v ee =- 5v input capacitance (control input) c c - 5 - pf - - input capacitance (switch input) c s - 10 - pf - - downloaded from: http:///
5/ 17 tsz02201-0rdr0gz00280-1-2 ? 20 15 rohm co., ltd. all rights reserved. 06.jan.2015 rev.001 www.rohm.com tsz22111 ? 15 ? 001 bu40 51 bc bu40 51 bcf bu4051bcfv waveforms of switching characteristics x1 to x7 (input) x (output) control (input) x (output) v ss v dd 50% t pzh 50% t p hz 90% control (input) x (output) figure 1. propagation delay time in out (t plh ,t phl ) wave form vdd vee, vss figure 4 . propagation delay time control (a,b,c,inhibit)out (t plh ,t phl ) test circuit r l c l out contr ol a b c inhibit x1 to x7 x vdd vee, vss figure 2 . propagation delay time inout (t plh ,t phl ) test circuit in r l c l out x vdd figure 3 . propagation delay time control (a,b,c,inhibit)out (t plh ,t phl ) wave form figure 5 . propagation delay time control (a,b,c,inhibit)out (t pzl ,t p lz ) vdd vee, vss r l control a b c inhibit x1 to x7 x out c l figure 6 . propagation delay time control (a,b,c,inhibit)out (t p zl ,t p lz ) test circuit t p lz v ss v dd 50% t pz l 50% 10% v dd v ee t plh t p hl 50% 50% control a b c inhibit x1 to x7 downloaded from: http:///
6/ 17 tsz02201-0rdr0gz00280-1-2 ? 20 15 rohm co., ltd. all rights reserved. 06.jan.2015 rev.001 www.rohm.com tsz22111 ? 15 ? 001 bu40 51 bc bu40 51 bcf bu4051bcfv typical performance curves figure 7 . on resistance vs input voltage v dd =3v figure 8 . on resistance vs input voltage v dd =5v figure 9 . on resistance vs input voltage v dd =10v figure 10 . on resistance vs input voltage v dd =15v 0 200 400 600 800 1000 1200 1400 0 1 2 3 4 5 input voltage [v] on resistance [] - 40 c 25 c 85 c 0 200 400 600 800 1000 1200 1400 0 1 2 3 4 5 input voltage [v] on resistance [] - 40 c 25 c 85 c 0 200 400 600 800 1000 1200 1400 0 2 4 6 8 10 input voltage [v] on resistance [] - 40 c 25 c 85 c 0 200 400 600 800 1000 1200 1400 0 3 6 9 12 15 input voltage [v] on resistance [] - 40 c 25 c 85 c downloaded from: http:///
7/ 17 tsz02201-0rdr0gz00280-1-2 ? 2014 rohm co., ltd. all rights reserved. 06.jan.2015 rev.001 www.rohm.com tsz22111 ? 15 ? 001 bu40 51 bc bu40 51 bcf bu4051bcfv typical performance curves - continued 0 10 20 30 40 50 -50 -25 0 25 50 75 100 ambient temperature [c] propagation delay time [ns] operating temperature range v dd =3v v dd =5v 0 10 20 30 40 50 -50 -25 0 25 50 75 100 ambient temperature [c] propagation delay time [ns] v dd =3v v dd =5v v dd =10v v dd =18v operating temperature range figure 11 . propagation delay time in out(t plh ) vs ambient temperature figure 12 . propagation delay time inout (t p hl ) vs ambient temperature figure 13 . propagation delay time control (a,b,c) out (t p zh ) vs ambient temperature figure 14 . propagation delay time control (a,b,c) out (t p hz ) vs ambient temperature v dd =18v v dd =10v 0 100 200 300 400 500 -50 -25 0 25 50 75 100 ambient temperature [c] propagation delay time [ns] v dd =3v v dd =5v v dd =10v v dd =18v operating temperature range 0 100 200 300 400 500 -50 -25 0 25 50 75 100 ambient temperature [c] propagation delay time [ns] operating temperature range v dd =18v v dd =10v v dd =5v v dd =3v downloaded from: http:///
8/ 17 tsz02201-0rdr0gz00280-1-2 ? 2014 rohm co., ltd. all rights reserved. 06.jan.2015 rev.001 www.rohm.com tsz22111 ? 15 ? 001 bu40 51 bc bu40 51 bcf bu4051bcfv typical performance curves - continued 0 100 200 300 400 500 -50 -25 0 25 50 75 100 ambient temperature [c] propagation delay time [ns] 0 100 200 300 400 500 -50 -25 0 25 50 75 100 ambient temperature [c] propagation delay time [ns] 0 100 200 300 400 500 -50 -25 0 25 50 75 100 ambient temperature [c] propagation delay time [ns] 0 100 200 300 400 500 -50 -25 0 25 50 75 100 ambient temperature [c] propagation delay time [ns] operating temperature range v dd =3v v dd =5v v dd =10v v dd =18v figure 15 . propagation delay time control (a,b,c) out(t pl z ) vs ambient temperature figure 16 . propagation delay time control (a,b,c) out(t p zl ) vs ambient temperature figure 17 . propagation delay time control (inhibit) out (t p zh ) vs ambient temperature figure 18 . propagation delay time control (inhibit) out (t p hz ) vs ambient temperature operating temperature range v dd =3v v dd =5v v dd =10v v dd =18v v dd =18v v dd =10v v dd =5v v dd =18v v dd =3v operating temperature range v dd =10v v dd =5v v dd =3v operating temperature range downloaded from: http:///
9/ 17 tsz02201-0rdr0gz00280-1-2 ? 20 15 rohm co., ltd. all rights reserved. 06.jan.2015 rev.001 www.rohm.com tsz22111 ? 15 ? 001 bu40 51 bc bu40 51 bcf bu4051bcfv typical performance curves - continued 0 100 200 300 400 500 -50 -25 0 25 50 75 100 ambient temperature [c] propagation delay time [ns] figure 19 . propagation delay time control (inhibit) out(t p zl ) vs ambient temperature figure 20 . propagation delay time control (inhibit) out(t p lz ) vs ambient temperature v dd =18v v dd =10v v dd =3v v dd =5v operating temperature range 0 100 200 300 400 500 -50 -25 0 25 50 75 100 ambient temperature [c] propagation delay time [ns] operating temperature range v dd =3v v dd =5v v dd =10v v dd =18v downloaded from: http:///
10/ 17 tsz02201-0rdr0gz00280-1-2 ? 20 15 rohm co., ltd. all rights reserved. 06.jan.2015 rev.001 www.rohm.com tsz22111 ? 15 ? 001 bu40 51 bc bu40 51 bcf bu4051bcfv power dissipation power dissipation (total loss) indicates the power that can be consumed by ic at t a =25c(normal temperature). ic is heated when it consumed power, and the temperature of ic c hip becomes higher than ambient temperature. the temperature that can be accepted by ic chip depends on circu it configuration, manufacturing process, and consumable power is limited. power dissipation is determined by the temp erature allowed in ic chip(maximum junction temperature) and thermal resistance of package(heat dissipation capability). the maximum junction temperature is typically equal to t he maximum value in the storage temperature range. heat generated by consumed power of ic radiates from the mold resin or lead frame of the package. the parameter which indicates this heat dissipation capability(hardness of heat release) is called ther mal resistance, represented by the symbol ja (c /w ).the temperature of ic inside the package can be estimated by this thermal resistance. figure 21 shows the model of thermal resistance of the package. th ermal resistance ja , ambient temperature t a , maximum junction temperature t jmax , and power dissipation p d can be calculated by the equation below: ja = (t jmax - t a ) / p d (c /w ) derating curve in figure 22 indicates power that can be consumed by ic with reference to ambient temperature. power that can be consumed by ic begins to attenuate at certain ambie nt temperature. this gradient is determined by thermal resistance ja . thermal resistance ja depends on chip size, power consumption, package, ambi ent temperature, package condition, wind velocity, etc even when the same of pack age is used. thermal reduction curve indicates a referenc e value measured at a specified condition. i/o equivalent circuits pin no. control input terminals input / output terminals 6,9,10,11 1,2,3,4,5,12,13,14,15 equivalence circuit vdd vdd gnd gnd vdd gnd figure 22 . derating curve figure 21 . thermal resistance ?? ta [ ] ? ? tj [ ] M p [w] ambient temperature t a ( ) chip surface temperature t j ( ) ja =( t jmax - t a )/ p d (c /w ) 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 0 25 50 75 100 125 150 ambient temperature [ ] power dissipation [w] bu4051bcf (sop16) 85 bu40 51 bcfv (ssop-b16) bu40 51 bc (dip16) v ss v ee vdd v dd v dd v ss downloaded from: http:///
11 / 17 tsz02201-0rdr0gz00280-1-2 ? 20 15 rohm co., ltd. all rights reserved. 06.jan.2015 rev.001 www.rohm.com tsz22111 ? 15 ? 001 bu40 51 bc bu40 51 bcf bu4051bcfv operational notes 1. reverse connection of power supply connecting the power supply in reverse polarity can damage the ic. take precautions against reverse polarity when connecting the power supply, such as mounting an extern al diode between the power supply and the ic s power supply pin s. 2. power supply lines design the pcb layout pattern to provide low impedance sup ply lines. separate the ground and supply lines of th e digital and analog blocks to prevent noise in the grou nd and supply lines of the digital block from affecting the analog block. furthermore, connect a capacitor to ground at all pow er supply pins . consider the effect of temperature and aging on the capacitance value when using electrolytic capa citors. 3. vdd voltage ensure that no pins are at a voltage above that of the vdd pin at any time, even during transient condition. 4. ground wiring pattern when using both small-signal and large-current ground traces , the two ground traces should be routed separately but connected to a single ground at the reference point of the application board to avoid fluctuations in the small- signal ground caused by large currents. also ensure that the ground traces of external components do not cause variations on the ground voltage. the ground lines must be as short and thick as possible to reduce line impedance. 5. thermal consideration should by any chance the power dissipation rating be exc eeded the rise in temperature of the chip may result in deterioration of the properties of the chip. the absolute ma ximum rating of the pd stated in this specification is whe n the ic is mounted on a 70mm x 70mm x 1.6mm glass epoxy b oard. in case of exceeding this absolute maximum rating, increase the board size and copper area to prevent excee ding the pd rating. 6. recommended operating conditions these conditions represent a range within which the expe cted characteristics of the ic can be approximately obtained . the electrical characteristics are guaranteed under the condi tions of each parameter. 7. inrush current when power is first supplied to the ic, it is possible that the internal logic may be unstable and inrush current may flow instantaneously due to the internal powering sequence and del ays, especially if the ic has more than one power supply. therefore, give special consideration to power c oupling capacitance, power wiring, width of ground wiring, and routing of connections. 8. operation under strong electromagnetic field operating the ic in the presence of a strong electromagnetic field m ay cause the ic to malfunction. 9. testing on application boards when testing the ic on an application board, connecting a capacitor directly to a low-impedance output pin may subject the ic to stress. always discharge capacitors completely after each p rocess or step. the ics power supply should always be turned off completely before connecting or removing it from the test setup during the inspection process. to prevent damage from static discharge, ground the ic during assembly and use similar precautions during transport and storage. 10. inter-pin short and mounting errors ensure that the direction and position are correct when mountin g the ic on the pcb. incorrect mounting may result in damaging the ic. avoid nearby pins being shorted to each other especially to ground, power supply and output pin . inter-pin shorts could be due to many reasons such as me tal particles, water droplets (in very humid environment) and unintentional solder bridge deposited in between pins du ring assembly to name a few. downloaded from: http:///
12 / 17 tsz02201-0rdr0gz00280-1-2 ? 20 15 rohm co., ltd. all rights reserved. 06.jan.2015 rev.001 www.rohm.com tsz22111 ? 15 ? 001 bu40 51 bc bu40 51 bcf bu4051bcfv operational notes C continued 11. unused input pins input pins of an ic are often connected to the gate of a mos trans istor. the gate has extremely high impedance and extremely low capacitance. if left unconnected, the elec tric field from the outside can easily charge it. the smal l charge acquired in this way is enough to produce a signi ficant effect on the conduction through the transistor and cause unexpected operation of the ic. so unless otherwise spe cified, unused input pins should be connected to the power supply or ground line. 12. regarding the input pin of the ic in the construction of this ic, p-n junctions are inevitabl y formed creating parasitic diodes or transistors. the operation of these parasitic elements can result in mutu al interference among circuits, operational faults, or physi cal damage. therefore, conditions which cause these parasitic elements to operate, such as applying a voltage to an input pin lower than the ground voltage should be avoid ed. furthermore, do not apply a voltage to the input pins when no power supply voltage is applied to the ic. even i f the power supply voltage is applied, make sure that th e input pins have voltages within the values specified in the e lectrical characteristics of this ic. 13. ceramic capacitor when using a ceramic capacitor, determine the dielectric constant considering the change of capacitance with temperature and the decrease in nominal capacitance due to dc bias a nd others. 14. area of safe operation (aso) operate the ic such that the output voltage, output current, and power dissipation are all within the area of safe operation (aso). downloaded from: http:///
13 / 17 tsz02201-0rdr0gz00280-1-2 ? 20 15 rohm co., ltd. all rights reserved. 06.jan.2015 rev.001 www.rohm.com tsz22111 ? 15 ? 001 bu40 51 bc bu40 51 bcf bu4051bcfv ordering information b u 4 0 5 1 b c x x - x x part number bu4051bc bu4051bcf bu4051bcfv package none : dip16 f one : sop16 fv : ssop-b16 packaging and forming specification none : tube e2 : embossed tape and reel (sop 16 / ssop-b16) marking diagrams sop16(top view) bu4051bcf part number marking lot number 1pin mark ssop-b16(top view) 4051c part number marking lot number 1pin mark dip 16 (top view) b u 4 0 5 1 b c part number marking lot number downloaded from: http:///
14 / 17 tsz02201-0rdr0gz00280-1-2 ? 20 15 rohm co., ltd. all rights reserved. 06.jan.2015 rev.001 www.rohm.com tsz22111 ? 15 ? 001 bu40 51 bc bu40 51 bcf bu4051bcfv physical dimension, tape and reel information package name dip 16 downloaded from: http:///
15 / 17 tsz02201-0rdr0gz00280-1-2 ? 20 15 rohm co., ltd. all rights reserved. 06.jan.2015 rev.001 www.rohm.com tsz22111 ? 15 ? 001 bu40 51 bc bu40 51 bcf bu4051bcfv physical dimension, tape and reel information - continued package name sop16 (unit : mm) pkg : sop16 drawing no. : ex114-5001 (max 10.35 (include.burr)) downloaded from: http:///
16 / 17 tsz02201-0rdr0gz00280-1-2 ? 20 15 rohm co., ltd. all rights reserved. 06.jan.2015 rev.001 www.rohm.com tsz22111 ? 15 ? 001 bu40 51 bc bu40 51 bcf bu4051bcfv physical dimension, tape and reel information - continued package name ssop-b16 downloaded from: http:///
17 / 17 tsz02201-0rdr0gz00280-1-2 ? 20 15 rohm co., ltd. all rights reserved. 06.jan.2015 rev.001 www.rohm.com tsz22111 ? 15 ? 001 bu40 51 bc bu40 51 bcf bu4051bcfv revision history date revision changes 06.jan.2015 001 new release downloaded from: http:///
datasheet d a t a s h e e t notice-ge rev.004 ? 2013 rohm co., ltd. all rights reserved. notice precaution on using rohm products 1. our products are designed and manufac tured for application in ordinary elec tronic equipments (such as av equipment, oa equipment, telecommunication equipment, home electroni c appliances, amusement equipment, etc.). if you intend to use our products in devices requiring ex tremely high reliability (such as medical equipment (note 1) , transport equipment, traffic equipment, aircraft/spacecra ft, nuclear power controllers, fuel c ontrollers, car equipment including car accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or serious damage to property (specific applications), please consult with the rohm sale s representative in advance. unless otherwise agreed in writing by rohm in advance, rohm shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any ro hms products for specific applications. (note1) medical equipment classification of the specific applications japan usa eu china class class class b class class ? class 2. rohm designs and manufactures its products subject to strict quality control system. however, semiconductor products can fail or malfunction at a certain rate. please be sure to implement, at your own responsibilities, adequate safety measures including but not limited to fail-safe desi gn against the physical injury, damage to any property, which a failure or malfunction of our products may cause. the following are examples of safety measures: [a] installation of protection circuits or other protective devices to improve system safety [b] installation of redundant circuits to reduce the impact of single or multiple circuit failure 3. our products are designed and manufactured for use under standard conditions and not under any special or extraordinary environments or conditio ns, as exemplified below. accordin gly, rohm shall not be in any way responsible or liable for any damages, expenses or losses arising from the use of an y rohms products under any special or extraordinary environments or conditions. if you intend to use our products under any special or extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of product performance, reliability, etc, prior to use, must be necessary: [a] use of our products in any types of liquid, incl uding water, oils, chemicals, and organic solvents [b] use of our products outdoors or in places where the products are exposed to direct sunlight or dust [c] use of our products in places where the products ar e exposed to sea wind or corrosive gases, including cl 2 , h 2 s, nh 3 , so 2 , and no 2 [d] use of our products in places where the products are exposed to static electricity or electromagnetic waves [e] use of our products in proximity to heat-producing components, plastic cords, or other flammable items [f] sealing or coating our products with resin or other coating materials [g] use of our products without cleaning residue of flux (ev en if you use no-clean type fluxes, cleaning residue of flux is recommended); or washing our products by using water or water-soluble cleaning agents for cleaning residue after soldering [h] use of the products in places subject to dew condensation 4. the products are not subjec t to radiation-proof design. 5. please verify and confirm characteristics of the final or mounted products in using the products. 6. in particular, if a transient load (a large amount of load applied in a short per iod of time, such as pulse. is applied, confirmation of performance characteristics after on-boar d mounting is strongly recomm ended. avoid applying power exceeding normal rated power; exceeding the power rating under steady-state loading c ondition may negatively affect product performance and reliability. 7. de-rate power dissipation (pd) depending on ambient temper ature (ta). when used in seal ed area, confirm the actual ambient temperature. 8. confirm that operation temperat ure is within the specified range described in the product specification. 9. rohm shall not be in any way responsible or liable for fa ilure induced under deviant condi tion from what is defined in this document. precaution for mounting / circuit board design 1. when a highly active halogenous (chlori ne, bromine, etc.) flux is used, the resi due of flux may negatively affect product performance and reliability. 2. in principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must be used on a through hole mount products. if the flow sol dering method is preferred on a surface-mount products, please consult with the rohm representative in advance. for details, please refer to rohm mounting specification downloaded from: http:///
datasheet d a t a s h e e t notice-ge rev.004 ? 2013 rohm co., ltd. all rights reserved. precautions regarding application examples and external circuits 1. if change is made to the constant of an external circuit, pl ease allow a sufficient margin considering variations of the characteristics of the products and external components, including transient characteri stics, as well as static characteristics. 2. you agree that application notes, re ference designs, and associated data and in formation contained in this document are presented only as guidance for products use. theref ore, in case you use such information, you are solely responsible for it and you must exercise your own independent verification and judgment in the use of such information contained in this document. rohm shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of such information. precaution for electrostatic this product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. please take proper caution in your manufacturing process and storage so that voltage exceeding t he products maximum rating will not be applied to products. please take special care under dry condit ion (e.g. grounding of human body / equipment / solder iron, isolation from charged objects, se tting of ionizer, friction prevention and temperature / humidity control). precaution for storage / transportation 1. product performance and soldered connections may deteriora te if the products are stor ed in the places where: [a] the products are exposed to sea winds or corros ive gases, including cl2, h2s, nh3, so2, and no2 [b] the temperature or humidity exceeds those recommended by rohm [c] the products are exposed to di rect sunshine or condensation [d] the products are exposed to high electrostatic 2. even under rohm recommended storage c ondition, solderability of products out of recommended storage time period may be degraded. it is strongly recommended to confirm sol derability before using products of which storage time is exceeding the recommended storage time period. 3. store / transport cartons in the co rrect direction, which is indicated on a carton with a symbol. otherwise bent leads may occur due to excessive stress applied when dropping of a carton. 4. use products within the specified time after opening a humidity barrier bag. baking is required before using products of which storage time is exceeding the recommended storage time period. precaution for product label qr code printed on rohm products label is for rohms internal use only. precaution for disposition when disposing products please dispose them proper ly using an authorized industry waste company. precaution for foreign exchange and foreign trade act since our products might fall under cont rolled goods prescribed by the applicable foreign exchange and foreign trade act, please consult with rohm representative in case of export. precaution regarding intellectual property rights 1. all information and data including but not limited to application example contained in this document is for reference only. rohm does not warrant that foregoi ng information or data will not infringe any intellectual property rights or any other rights of any third party regarding such information or data. rohm shall not be in any way responsible or liable for infringement of any intellectual property rights or ot her damages arising from use of such information or data.: 2. no license, expressly or implied, is granted hereby under any intellectual property rights or other rights of rohm or any third parties with respect to the information contained in this document. other precaution 1. this document may not be reprinted or reproduced, in whol e or in part, without prior written consent of rohm. 2. the products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written consent of rohm. 3. in no event shall you use in any wa y whatsoever the products and the related technical information contained in the products or this document for any military purposes, incl uding but not limited to, the development of mass-destruction weapons. 4. the proper names of companies or products described in this document are trademarks or registered trademarks of rohm, its affiliated companies or third parties. downloaded from: http:///
datasheet datasheet notice C we rev.001 ? 201 5 rohm co., ltd. all rights reserved. general precaution 1. before you use our pro ducts, you are requested to care fully read this document and fully understand its contents. rohm shall n ot be in an y way responsible or liabl e for fa ilure, malfunction or acci dent arising from the use of a ny rohms products against warning, caution or note contained in this document. 2. all information contained in this docume nt is current as of the issuing date and subj ec t to change without any prior notice. before purchasing or using rohms products, please confirm the la test information with a rohm sale s representative. 3. the information contained in this doc ument is provi ded on an as is basis and rohm does not warrant that all information contained in this document is accurate an d/or error-free. rohm shall not be in an y way responsible or liable for an y damages, expenses or losses incurred b y you or third parties resulting from inaccur acy or errors of or concerning such information. downloaded from: http:///

▲Up To Search▲

Price & Availability of BU4051BCFV-E2

	To Download BU4051BCFV-E2 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .